Slip Granules

DESCRIPTION

FT6236 is a Low Density Polyethylene for Film extrusion produced by high pressure Tubular Technology. This product is developed for the production of packaging film with good optical properties.

FT6236 contains Slip, Antiblock & antioxidant additives

APPLICATIONS

• FFS Bags :- General Purpose Pouches
• Lamination :- Shopping Bags/ High Gloss Films
• Food Packaging  :- Laundry Bags

KEY FEATURES

• Excellent process ability :- Excellent Optical Properties
• Easy Sealing :- Low COF

FOOD CONTACT REGULATIONS

FT6236 fulfils the food contact regulations in most countries. If required, contact your Borouge representative for a certificate

STORAGE

This product should be stored in dry conditions at temperature bellow 50°C and protected from UV-light. Improper storage can initiate degradation, which results in odour generation and colour changes and can have negative effects on physical properties of this product. More information on storage can be found in Safety Information Sheet (SIS) for this product.

SAFETY

The product is not classified as a hazardous mixture.

Dust and fines from the product carry a risk of dust explosion. All equipment should be properly earthed. Inhalation of dust should be avoided as it may cause irritation of the respiratory system. Small amounts of fumes are generated during processing of the product. Proper ventilation is therefore required.

Please see our Safety Information Sheet (SIS) for details on various aspects of safety, recovery and disposal of the product, for more information contact your Borouge representative

RECYCLING

The product is suitable for recycling using modern methods of shredding and cleaning. In-house production waste should be kept clean to facilitate direct recycling.

Product Description

Lupolen 2427 H is an additivated, low density polyethylene. It contains an antioxidant, slip and anti-blocking agent. It is characterized by a good balance between processability and mechanical properties. Films made from Lupolen 2427 H exhibit good optical properties. It is delivered in pellet form

This product is not intended for use in medical and pharmaceutical applications.

Status :- Commercial: Active

Availability :- Africa-Middle East; Asia-Pacific; Europe

Application :- Bags & Pouches; Food Packaging Film; Hygiene Film; Liner Film; Shrink Film

Market :- Flexible Packaging

Processing Method :- Blown Film; Cast Film

Attribute :- Antioxidant; Good Heat Seal; Good Optical Properties; Good Processability; Low

Friction; Unspecified Antiblocking; Unspecified Slip

Processing Techniques

Users should determine the conditions necessary to obtain optimum product properties and suitability of the product for the intended application. In cases where higher temperatures are required, please contact your appropriate technical contact for support.

Health and Safety

The resin is manufactured to the highest standards, but special requirements apply to certain applications such as food end-use contact and direct medical use. For specific information on regulatory compliance contact your local representative.

Workers should be protected from the possibility of skin or eye contact with molten polymer. Safety glasses are suggested as a minimal precaution to prevent mechanical or thermal injury to the eyes.

Molten polymer may be degraded if it is exposed to air during any of the processing and off-line operations. The products of degradation may have an unpleasant odor. In higher concentrations they may cause irritation of the mucus membranes. Fabrication areas should be ventilated to carry away fumes or vapours. Legislation on the control of emissions and pollution prevention should be observed.

The resin will burn when supplied with excess heat and oxygen. It should be handled and stored away fromcontact with direct flames and/or ignition sources. While burning, the resin contributes high heat and may generate a dense black smoke.

Conveying:

Conveying equipment should be designed to prevent production and accumulation of fines and dust particles that are contained in polymer resins. These particles can under certain conditions pose an explosion hazard. Conveying systems should be grounded, equipped with adequate filters and regularly inspected for leaks.

Storage:

The resin is packed in 25 kg bags, octabins or bulk containers protecting it from contamination. If it is stored under certain conditions, i. e. if there are large fluctuations in ambient temperature and the atmospheric humidity is high, moisture may condense inside the packaging. Under these circumstances, it is recommended to dry the resin before use. Unfavorable storage conditions may also intensify the resin's slight characteristic odor.Resin should be protected from direct sunlight, temperatures above 40°C and high atmospheric humidity during

storage. Higher storage temperatures may reduce the storage time. The information submitted is based on our current knowledge and experience. In view of the many factors that may affect processing and application, these data do not relieve processors of the responsibility of carrying out their own tests and experiments; neither do they imply any legally binding assurance of certain properties or of

suitability for a specific purpose. This information does not remove the obligation of the customer to inspect the material on arrival and notify us of any faults immediately. It is the responsibility of those to whom we supply our products to ensure that any proprietary rights and existing laws and legislation are observed