PP CP Granules

Product Description

Moplen EP332L is a heterophasic copolymer with medium flow used in injection molding. This grade is characterized by a medium stiffness-impact balance at low temperature as well as a low warpage tendency. The additive formulation provides a good heat aging resistance. Moplen EP332L is typically used by customers requiring a high resistance to temperature degradation, in particular for battery cases and automotive components.

This grade is not intended for medical and pharmaceutical applications.

Status Commercial: Active

Availability Africa-Middle East; Asia-Pacific; Australia and New Zealand; Europe; South & Central America

Application Battery Cases

Market Automotive; Consumer Products; Industrial, Building & Construction

Processing Method Injection Molding

Attribute Good Heat Aging Resistance; Good Impact Resistance; Good Stiffness; Heat

Stabilized; Impact Copolymer; Low Warpage

Health and Safety

The resin is manufactured to the highest standards, but special requirements apply to certain applications such as food end-use contact and direct medical use. For specific information on regulatory compliance contact you ocal representative.

Workers should be protected from the possibility of skin or eye contact with molten polymer. Safety glasses are suggested as a minimal precaution to prevent mechanical or thermal injury to the eyes.

Molten polymer may be degraded if it is exposed to air during any of the processing and off-line operations. The products of degradation may have an unpleasant odor. In higher concentrations they may cause irritation of the mucus membranes. Fabrication areas should be ventilated to carry away fumes or vapours. Legislation on the control of emissions and pollution prevention should be observed.

DESCRIPTION

BD265MO is a very high impact heterophasic copolymer based on proprietary Borstar Nucleation Technology (BNT). This product exhibits excellent impact strength even at low temperatures and good processability and stiffness properties Articles produced with this grade exhibit very good demoulding properties and dimensional consistency with respect to different colours.

APPLICATION

• Juvenile care
• Toys
• Crates, boxes and pallets
• Heavy duty pails
• Furniture Technical applications

SPECIAL FEATURES

• Very high impact strength
• Efficient processing with BNT
• Good demoulding
• Excellent dimensional stability

PROCESSING CONDITIONS

BD265MO is easy to process with standard injection moulding machines.

Following parameters should be used as guidelines:

Melt temperature: 220 - 260°C

Holding pressure: 200 - 500bar As required to avoid sink marks

Mould temperature: 10 - 40°C

Injection speed: As high as possible

Shrinkage 1 - 2%, depending on wall thickness and moulding parameters

STORAGE

BD265MO should be stored in dry conditions at temperatures below 50°C and protected from UV-light. Improper storage can initiate degradation, which results in odour generation and colour changes and can have negative effects on the physical properties of this product. More information on storage can be found in Safety Information Sheet (SIS) for this product

SAFETY

The product is not classified as a hazardous preparation. Please see our Safety Information Sheet (SIS) for details on various aspects of safety, recovery and disposal of the product, for more information contact your Borouge representative.

RECYCLING

The product is suitable for recycling using modern methods of shredding and cleaning. In-house production waste should be kept clean to facilitate direct recycling.

DESCRIPTION

BJ368MO is a heterophasic copolymer characterized by very high flow, and optimum combination of high stiffness and impact strength.

The material is nucleated with Borstar Nucleation Technology (BNT). Flow properties, nucleation and good stiffness give potential for cycle time reduction.

The material has both good antistatic performance and mould release properties\

APPLICATIONS

• Thin wall containers
• Food packaging
• Small size ice cream containers

SPECIAL FEATURES

• Very good stiffness and impact balance
• Good flow behaviour
• Reduced cycle time and increased output

PROCESSING CONDITIONS

BJ368MO is easy to process with standard injection moulding machines.

Following parameters should be used as guidelines:

Melt temperature: 210 - 260°C

Holding pressure: 200 - 500bar As required to avoid sink marks

Mould temperature: 10 - 30°C

Injection speed: As high as possible

Shrinkage 1 - 2%, depending on wall thickness and moulding parameters

STORAGE

BJ368MO should be stored in dry conditions at temperatures below 50°C and protected from UV-light. Improper storage can initiate degradation, which results in odour generation and colour changes and can have negative effects on the physical properties of this product.

SAFETY

The product is not classified as a hazardous preparation. Please see our Safety Information Sheet (SIS) for details on various aspects of safety, recovery and disposal of the product, for more information contact your Borouge representative.

RECYCLING

The product is suitable for recycling using modern methods of shredding and cleaning. In-house production waste should be kept clean to facilitate direct recycling.

DESCRIPTION

SABIC® PP 37MK10 is a impact copolymer polypropylene resin and is typically used for industrial injection molding application. Molded parts made from this resin typically exhibits good impact, high stiffness and good heat stability. This product is formulated with nucleating agent.

TYPICAL APPLICATIONS

SABIC® PP 37MK10 can be used to produceCrates, electrical appliances, thin wall applications and industrial applications

PROCESSING CONDITIONS

Typical Processing conditions for 37MK10 are:

Recommended melt temperature : 190 – 230 °C

STORAGE AND HANDLING

Polypropylene resin should be stored in a manner to prevent a direct exposure to sunlight and/or heat. The storage area should also be dry and preferably do not exceed 50°C. SABIC would not give warranty to bad storage conditions which may lead to quality deterioration such as color change, bad smell and inadequate product performance. It is advisable to process PP resin within 6 months after delivery.